News   

  Home   

  Publications  

  DataBase  

  FAQs  

  Contact  

  Applications   

You are about to be redirected to the new
Copper Development Association Site

www.copperinfo.co.uk

with improved navigation and full searchability.

Please remember to bookmark the new page!

Publication 120
Copper & Copper Alloys
Compostitions, Applications & Properties

120_web.jpg (6492 bytes)

The EN series of standards for copper and copper alloys offers a selection of materials to suit a very wide variety of end uses.  They represent a consensus agreement on those most frequently ordered by consumers.  This revised publication summarises the main compositions and the range of properties - the contents list is outlined below.

Whilst our publication has been prepared with care, we can give no warranty regarding the contents and shall not be liable for any direct, incidental or consequential damage arising out of its use.  For complete information on any material the appropriate standard should be consulted.

Order your copy now - £10.00 including p&p

Contents List
Introduction to Standards
Introduction (351KB) Introduction to Standards
Table 1 (518KB) EN Standards for Copper and Copper Alloys
Table 2 (562KB) Listing of Old BS Standards replaced by EN Standards
Section 1: Conversion of old BS into EN Material Designations
Table 3

(527KB)

 Unwrought and Wrought Coppers - Conversion of Old BS into EN Material Designations
Table 4 (537KB) Wrought Copper Alloys - Conversion olf Old BS into EN Material Designations
Table 5 (539 KB) Copper and Copper Alloy Ingots and Castings - Comparison of BS1400 and EN 1982
Section 2: EN Coppers and Copper Alloys
Table 6a

(544KB)

 Unwrought and Wrought Coppers - Compositions, Uses and Typical Properties
Table 6b (538KB) Unwrought and Wrought Coppers - Relevant Standards
Table 7 (1035KB) EN 1982 Copper and Copper Alloy Ingots and Castings - Compositions, Uses & Typical Properties
Table 8 (533KB) Wrought Low-Alloyed Copper Alloys - Compositions, Uses, Typical Mechanical Properties, Relevant Standards and Approximate Electrical Conductivity
Table 9 (535KB) Wrought Copper-aluminium, Copper-nickel and Copper-nickel-zinc Alloys - Compositions, Uses, Typical Properties, Relevant Standards and Machinability
Table 10 (533KB) Wrought Copper-zinc and Copper-tin Binary Alloys - Compositions, Uses and Typical Properties
Table 11 (533KB) Wrought Copper-zinc-lead Alloys (Leaded Brasses) - Compositions, Uses, Typical Properties, Relevant Standards and Machinability
Table 12a (531KB) Wrought, Complex, Copper-zinc Alloys (Special Brasses) - Compositions, Uses and Typical Properties
Table 12b (528KB) Wrought, Complex, Copper-zinc Alloys (Special Brasses) - Relevant Standards
Table 13 (532KB) Copper and Copper Alloys for Welding and Braze Welding - Composition and Melting Ranges (EN 13347)
Section 3: Brass Semi-Finished Products
Table 14 (533KB) Brass Rods and Sections - Compositions, Uses and Typical Properties
Table 15 (530KB) Brass Forgings, Stampings and Hot Pressings - Compositions, Uses and Typical Properties
Table 16 (531KB) Brass Sheet, Strip and Plate - Compositions, Uses and Typical Properties
Table 17 (529KB) Brass Tubes - Compositions, Uses and Typical Properties
Table 18 (529KB) Brass Wire - Compositions, Uses and Typical Properties
To order a copy of Publication 120
The cost of this publication is £10 including postage within the UK.
Postage charged extra for overseas orders.

To order a copy of this publication please contact our helpline on 01442 275700.
Alternatively print a copy of the order form and return it to us.